There may be mechanical interference preventing the Roomba from leaving the base. Check the charging contacts on both the underside of the Roomba and the top of the homebase.
Why does my Roomba keep docking?
For those who don’t know, the Roomba is a vacuuming robot. Therefore, it will return to the home base to dock itself once the cleaning cycle is over or it runs out of battery. … This means you don’t have to wait for the cleaning cycle to be over or until the battery gets low.
Why does my Roomba keep return to base?
Roomba cleans an entire level of your home during one cleaning cycle. If its battery gets low before finishing a cleaning cycle, Roomba returns to the Home Base to recharge. … It will return to its starting location and the cleaning cycle will end.
How do I reset my Roomba docking station?
How to Reset My Roomba Cleaner?
- #1: Put your robot on the home base or directly contact the charger to the robotic cleaner.
- #2: Press and hold the CLEAN button for up to 10 seconds and wait for the blue-colored text ‘r 5Y’ to show up.
How do I send my Roomba back to the dock?
How to Send Roomba Home to Dock
- Verify that the home base is plugged in. If it’s not, your Roomba will be unable to locate it to dock. …
- Pick the Roomba up and set it down within five feet of the home base.
- Press the “Spot” and “Clean” buttons simultaneously. The Roomba will now drive into the home base to dock.
Where is the best place to put my Roomba dock?
- At least >1.5 ft (0.5 m>) on each side of the Home Base®.
- At least >4 ft (1.2 m>) in front of the Home Base®, with no furniture such as tables or chairs within this area.
- At least >4 ft (1.2 m>) between the Home Base® and any stairs.
- At least >8 ft (2.4 m>) from Virtual Wall® barriers.
How does Roomba know to dock?
When the battery power is running low, the robot uses its infrared sensors to locate the charging dock, which also emits infrared beams. The Roomba then follows the beams’ path toward the dock where it can recharge before resuming the cleaning session.
Can I move my Roomba docking station?
You can move a Roomba base. Your Roomba base location is mapped into the robot to ensure it finds its way back and recharges itself to continue cleaning or retire after cleaning, but nothing says your Roomba can’t find its way back to this base even after it has been moved.
How do I turn off Roomba for transport?
For long-term storage, turn off the robot by removing it from the charging station and holding down for 10 seconds. Store the robot in a cool, dry place. Your robot will tell you something is wrong by playing an audio alert and turning the light ring indicator red.
How do I reset my Roomba map?
Roomba i Series Reset:
- Press and Hold the HOME, SPOT CLEAN, and CLEAN buttons at the same time.
- Wait for the white light ring around the CLEAN button swirls.
- Release the 3 buttons.
- The Roomba will restart to finish the factory reset.
Can you charge Roomba without docking station?
Yes you can run your Roomba without the home base. All you have to do is plug the charger in the Roomba to charge it. It will stop on it’s own when it’s done. If you have a schedule set, the Roomba is plugged in while charging, it won’t execute the schedule.
How do I reprogram my Roomba?
Press and hold the Home, Spot Clean, and Clean buttons simultaneously. Then, wait for the light ring around the Clean button to begin swirling. Once there’s a light ring, let go of the three buttons. Now, the Roomba will restart, signaling the end of the factory reset process.
Why does Roomba bumper keep getting stuck?
Diane, this can be caused by dirty or defective bumper sensor as well as dirty cliff sensors. Clean the Roomba with compressed air and “slap” the front bumper. Apparently, the front bumper mechanism can get stuck with any contact with a wall etc. which will make the Roomba back up.
Why does Roomba get stuck on rug?
Running into an obstacle is the most common reason why your Roomba keeps getting stuck. Furniture, thick rugs, and cables are just some of the obstacles that your automatic vacuum can get stuck on.